North America · softwood
Western redcedar
Thuja plicata, Cupressaceae
Read the practical guide to Western redcedarJanka hardness
350 lbf
Harder than 2% of the 571 species with a laboratory test.
At a glance
- Janka hardness
- 350 lbf
- USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
- Density
- 22.3 lb/ft³
- USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
- Volumetric shrinkage
- 6.8%
- USDA Wood Handbook 2021 (FPL-GTR-282) Table 4-3
- Availability · editorial
- Widely stocked
Working characteristics: The wood works well with both hand tools and machine operations. Alden — Softwoods of North America (1997), FPL-GTR-102
Shrinkage is green to ovendry, not seasonal movement. Availability is an editorial guide, not a stock check.
Sourced wood and tree images
Each image names its author, its licence, and the page it came from.

WoodCirad · Public domain · Cirad xylothèque via Wikimedia Commons 
WoodCirad · Public domain · Cirad xylothèque via Wikimedia Commons 
WoodTedder at en.wikipedia · CC BY-SA 2.5 · Wikimedia Commons 
WoodGeordie.birch · CC BY-SA 4.0 · Wikimedia Commons 
WoodDavid Prasad from Welches, OR., United States · CC BY-SA 2.0 · Wikimedia Commons 
WoodPhoto by TJ Watt · CC BY-SA 3.0 · Wikimedia Commons 
BarkLoren Lane (MORA) · Public domain · Wikimedia Commons 
BarkChris Light · CC BY-SA 4.0 · Wikimedia Commons 
Treeabdallahh from Montréal, Canada · CC BY 2.0 · Wikidata via Wikimedia Commons 
TreeJ Brew · CC BY-SA · iNaturalist 
TreeJohn A Haskins · CC BY · iNaturalist
Geographic distribution
Where it grows
Recorded distribution of Thuja plicata. Native areas are part of its natural range; introduced areas are places where it has been brought by people.
Loading world map…
Native range (8 regions)
Alaska · Alberta · British Columbia · California · Idaho · Montana · Oregon · Washington
Introduced range (12 regions)
Austria · Denmark · Føroyar · Germany · Great Britain · Ireland · Italy · Norway · Poland · Portugal · Spain · Sweden
Shading marks botanical regions with recorded presence, not the exact extent of forests or commercial plantations. Large countries may be divided into states or provinces. Extinct and doubtful records are excluded. Unshaded areas have no record in this dataset; they do not prove absence.
Source: Kew species record · WCVP, version 16 (June 2026), Royal Botanic Gardens, Kew, CC BY 3.0. Map boundaries: TDWG / WGSRPD; adapted to a world map.
Measured properties
Dry-wood properties are shown for comparison; published moisture conditions can differ between sources. Shrinkage is from green to ovendry, not seasonal movement. Actual properties in service vary.
- Janka hardness
- 350 lbf
- Density at 12% MC
- 22.3 lb/ft³
- Specific gravity
- 0.32
- Modulus of rupture
- 7,500 lb/in²
- Modulus of elasticity
- 1.11 ×10⁶ lb/in²
- Crushing strength
- 4,560 lb/in²
- Radial shrinkage
- 2.4%
- Tangential shrinkage
- 5.0%
- Volumetric shrinkage
- 6.8%
USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
USDA Wood Handbook 2021 (FPL-GTR-282) Table 4-3
USDA Wood Handbook 2021 (FPL-GTR-282) Table 4-3
USDA Wood Handbook 2021 (FPL-GTR-282) Table 4-3
Where these numbers come from
Check the references below to see which properties each source supports.
- USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
Janka hardness · Green wood hardness · Specific gravity · Basic specific gravity · Density · Bending strength · Stiffness · Crushing strength · Green wood properties
- USDA Wood Handbook 2021 (FPL-GTR-282) Table 4-3
Shrinkage
- USDA FIA REF_SPECIES
Scientific name
- GWDD v2.2 (Fischer et al. 2026)
Botanical family
Western redcedar wood: a practical guide
Western redcedar (Thuja plicata) is listed as a softwood from North America. The source descriptions below explain its appearance, working characteristics, and documented uses where those have been published. Use this guide to connect that evidence to buying stock, choosing a project, and planning the work.
Species and group descriptions are attributed below. Practical recommendations explain how to use the available evidence; they are editorial guidance. Estimates and missing properties remain identified. Historical uses describe the source’s publication period.
What is Western redcedar?
The botanical name used by this record is Thuja plicata, in the Cupressaceae family. When buying, ask the supplier to identify the species rather than relying on the common name alone.
Historical source excerpt · Alden — Softwoods of North America (1997), FPL-GTR-102 · public domain
Source profile: Thuja plicata
Western redcedar grows in the Pacific Northwest and along the Pacific coast to Alaska. Western redcedar lumber is produced principally in Washington, followed by Oregon, Idaho, and Montana. The tree has been planted in Great Britain and New Zealand.
Common names can vary between countries and suppliers. For a restoration, repeat order, or technical specification, keep the botanical name and the supplier’s description with the material record.
A broad region describes this database entry, not the origin of the board offered for sale. Verify the shipment’s origin and sourcing documents if these affect your purchase. A description in an older timber reference also does not establish present-day availability.
General workshop reference: USDA Wood Handbook (public domain)
Color, grain, and choosing visible boards
The attributed descriptions below are a starting point for recognizing color and grain. Compare them with clean, freshly surfaced stock; oxidation, drying, lighting, and a coating can all change what a sample looks like.
Historical source excerpt · Alden — Softwoods of North America (1997), FPL-GTR-102 · public domain
Source profile: Thuja plicata
The heartwood of western redcedar is reddish or pinkish brown to dull brown and the sapwood nearly white. The sapwood is narrow, often not more than 1 in. (2.54 cm) in width. The wood is generally straight grained and has a uniform but rather coarse texture. It has very low shrinkage. This species is light in weight, moderately soft, low in strength when used as beams or posts, and low in shock resistance.
For visible work, buy the boards as a set. Decide whether changes between sapwood and heartwood are welcome, and lay out adjacent parts before cutting. A small attractive sample may not show the range of color or figure in a full order.
- Color match: evaluate the actual faces that will be visible, with the intended finish on a spare piece.
- Grain direction: follow the fibers through narrow parts, joints, and curved shapes; decorative figure can complicate cutting.
- Soundness: check both ends and faces for splits, decay, loose knots, and defects that reduce usable length.
General workshop reference: USDA Wood Handbook (public domain)
Hardness, weight, and strength in practice
Each property answers a different question. Janka side hardness compares indentation resistance, density helps with handling weight, stiffness relates to deflection, and bending strength concerns failure. None can stand in for all the others.
- Janka hardness: 350 lbf.Source: USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b (public domain).
- Density: 22.3 lb/ft³.Source: USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b (public domain).
- Bending strength: 7,500 lb/in².Source: USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b (public domain).
- Stiffness: 1.11 ×10⁶ lb/in².Source: USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b (public domain).
- Compression parallel to grain: 4,560 lb/in².Source: USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b (public domain).
Uses and project selection for Western redcedar
The source’s use list records applications reported when that reference was compiled. It can suggest where the material has been useful, but each finished product still needs stock, construction, and specifications suited to the job.
Historical source excerpt · Alden — Softwoods of North America (1997), FPL-GTR-102 · public domain
Source profile: Thuja plicata
Western redcedar is used principally for shingles, saunas, outdoor furniture, decking, fencing, lumber, poles, posts, and piles. The lumber is used for exterior siding, interior finish, greenhouse construction, ship and boat building, boxes and crates, sash, doors, and millwork.
The measured hardness is below that of many furniture hardwoods. Prioritize protection from dents and generous bearing areas beneath fasteners; consider whether the project needs a harder wearing surface.
Based on the recorded density, handling weight may be an advantage for larger parts. Check the actual stock and design connections for its properties rather than substituting dimensions from a heavier wood.
- Furniture and cabinetry: check visible color, grain at joints, stiffness for spans, and room for solid panels to move.
- Wear surfaces: compare measured hardness and the complete flooring or worktop specification, including coating and maintenance.
- Small turned or carved objects: inspect the blank’s soundness and make a cutting trial before choosing a thin profile.
- Outdoor or wet service: require decay-resistance and exposure evidence, together with drainage, hardware, and treatment details where applicable.
General workshop reference: USDA Wood Handbook (public domain)
Sawing, planing, routing, and drilling
Use the published working description below to plan the first trial. The following steps are general workshop recommendations; they are not a tested feed-rate schedule for this species.
Historical source excerpt · Alden — Softwoods of North America (1997), FPL-GTR-102 · public domain
Source profile: Thuja plicata
The wood works well with both hand tools and machine operations. It may splinter when worked on the end grain (e.g., mortising). It is subject to compression during planing and molding. It nails and screws well and takes both stains and paint satisfactorily.
- Start with sound stock: locate checks, short grain, and other defects before holding the work or setting the cut.
- Plane a trial face: read the grain and begin with a light pass. If grain reverses or tears, adjust the cut and consider scraping or sanding rather than repeatedly cutting deeper.
- Check heat and rubbing: sharp, clean cutters and a suitable feed help. Investigate burn marks instead of forcing a cut; follow the machine and cutter instructions.
- Back up exit edges: use suitable support when drilling or machining joints to reduce breakout. Trial-fit joinery before glue-up.
- Test fasteners: size pilot and clearance holes for the actual screw and stock. Dense material may split near an end, while softer material may crush beneath a fastener.
- Inspect the surface: use raking light to find machining marks, sanding scratches, and glue contamination before coating.
General workshop reference: USDA Wood Handbook (public domain)
Drying, shrinkage, and seasonal movement
Recorded green-to-ovendry shrinkage: radial 2.4%; tangential 5.0%; volumetric 6.8%. Source: USDA Wood Handbook 2021 (FPL-GTR-282) Table 4-3 (public domain). These describe drying over a much wider moisture range than a typical finished interior piece experiences.
Tangential shrinkage is about 2.1 times radial shrinkage, calculated from the published values. Growth-ring orientation therefore belongs in the selection of a wide panel. The ratio describes directional differences; it does not measure the total seasonal movement or prove that a board will remain flat.
Bring stock close to the conditions in which the finished object will live before final sizing and assembly. Check moisture with a meter used according to its instructions and the appropriate species correction. Kiln-dried does not mean that the wood is at the right moisture content for every room or climate.
- Wide tops: choose attachments that permit cross-grain movement, such as correctly installed clips or screws in appropriately oriented slots.
- Frame-and-panel work: allow the panel to move within the frame, following the chosen construction method.
- Freshly sawn lumber: use a drying schedule appropriate to the material and thickness; the shrinkage table is not a kiln schedule.
General workshop reference: USDA Wood Handbook (public domain)
Gluing and assembly
Prepare sound, properly fitted surfaces and make a complete dry assembly before spreading glue. Choose an adhesive for the intended exposure and follow its requirements for moisture, temperature, open time, pressure, and cure.
A species description that mentions natural oils, extractives, or difficult bonding is a reason to verify the adhesive system on the actual stock. Do not assume that sanding finer or wiping with an arbitrary solvent will solve an adhesion problem. Use the adhesive manufacturer’s preparation guidance.
Clamp pressure should close a well-made joint. If it takes excessive force to bring the pieces together dry, correct the fit or the stock first. Remove glue contamination before finishing and check corners, shoulders, and exposed end grain.
General workshop reference: USDA Wood Handbook (public domain)
Finishing, staining, and surface preparation
Choose the finish for the object’s use and the appearance you want. A clear coating reveals natural variation; a stain can emphasize differences in absorption. A decorative object, dining table, and exterior component need different protection and maintenance.
Do not infer finishing behavior from color or density alone. Open pores may influence the desired surface texture, while uneven absorption may complicate a uniform stain. Confirm the treatment on an offcut rather than selecting a pore filler, conditioner, or sealer by habit.
- Prepare consistently: remove marks from each sanding stage and inspect under raking light.
- Sample the whole system: reproduce the sanding, any color treatment, and the topcoat on stock from the project.
- Include end grain: test it when it will remain visible, since it can take color differently from the face.
- Check the result in use: allow the sample to dry and cure as directed, then examine it in the intended lighting.
General workshop reference: USDA Wood Handbook (public domain)
Decay resistance, exposure, and care
Read the source’s durability statement with its scope in mind. Heartwood, sapwood, resistance to a particular insect, and performance in a particular test are different things. An older durability report is useful background, not a service-life warranty.
Historical source excerpt · Alden — Softwoods of North America (1997), FPL-GTR-102 · public domain
Source profile: Thuja plicata
The heartwood of western redcedar is resistant to very resistant to decay. It is not immune to attack by termites and furniture beetles.
For interior pieces, follow the coating’s cleaning instructions and deal with spills promptly. Persistent dampness, trapped water at joints, and an unsuitable indoor humidity range need attention even when the surface appears well finished.
For exterior work, choose a documented material or product for the exposure. Provide drainage, avoid water-trapping pockets, and use compatible hardware. Ground contact and marine exposure demand more than a general statement that a timber is durable.
General workshop reference: USDA Wood Handbook (public domain)
Buying Western redcedar: a practical checklist
Price depends on the usable stock, not just a species name. Thickness, clear lengths, figure, color selection, drying, surfacing, quantity, and supply all affect the value of a quote. Compare like-for-like dimensions and include machining waste.
For an unfamiliar species or a large order, start with a sample and a small trial. Keep the supplier’s identification, stock condition, and sourcing information with the job so you can explain or repeat the choice later.
- Identity: confirm the botanical name and whether the shipment is a mixture or a single species.
- Moisture: ask about drying history and check the stock against the intended application.
- Usable dimensions: allow for flattening, trimming, checks, knots, and defects around the parts you need.
- Appearance: inspect the actual lot together if matching pale faces, heartwood color, or figure matters.
- Specification: obtain appropriate grade or product evidence for structural or demanding service.
- Supply and origin: check the actual shipment’s documentation; a reference-book entry does not prove current availability or permission to trade.
General workshop reference: USDA Wood Handbook (public domain)
Dust, food contact, and care
The occupational-source record linked to Western redcedar reports asthma, central nervous system effects, dermatitis, mucous membrane irritation, rhinitis. The botanical name matched the source entry, so this record is about this species.
Read the reported effects, source evidence, and match confidence for Western redcedar.
For a cutting board, utensil, or other food-contact object, confirm the material’s identity and history separately from its hardness. Unknown treatments, coatings, decay, and hard-to-clean defects can rule out a piece that otherwise looks attractive.
- Adhesive and finish: select products intended for the application and observe the manufacturer’s curing instructions.
- Cleaning: USDA advises washing cutting boards with hot, soapy water, rinsing, and drying after use. Keep raw-meat preparation separate from ready-to-eat foods.
- Condition: replace cutting boards when wear or grooves make them difficult to clean. Follow the care instructions for the construction; laminated boards can split in a dishwasher.
Comparing alternatives
The nearby measured-hardness values below help put dent resistance in context. Use appearance, movement, machining, supply, and exposure evidence to decide whether a different species is a practical substitute.
| Wood | Janka | Density |
|---|---|---|
| Western redcedarThuja plicata | 350 lbf | 22.3 lb/ft³ |
| Northern white cedarThuja occidentalis | 320 lbf | 21.7 lb/ft³ |
| Balsam firAbies balsamea | 380 lbf | 24.5 lb/ft³ |
| Eastern white pinePinus strobus | 380 lbf | 24.5 lb/ft³ |
Before you build
- Confirm the species and the usable dimensions of the stock.
- Check the properties that matter to the part, including any estimates or gaps.
- Match moisture to the intended environment and allow cross-grain movement.
- Make representative cutting, bonding, and finishing trials.
- Keep the approved sample, product details, and care instructions with the job.
Sources and further reading
Quoted descriptions retain the source’s scope and historical context. General workshop advice draws on the Wood Handbook; it is not a claim that every operation or application has been tested on this species. Figures above retain the property record’s named sources and licences.
- Alden — Softwoods of North America (1997), FPL-GTR-102
Thuja plicata · species description · public domain. Historical species descriptions. Nursery, medicinal, and industrial uses mentioned by the source are not instructions for making a product.
- USDA Wood Handbook 2021 (FPL-GTR-282) Table 5-3b
public domain. Supports: janka lbf, janka n, janka green lbf, specific gravity 12, specific gravity basic, density kg m3, mor psi, moe mpsi, crushing psi, green.
- USDA Wood Handbook 2021 (FPL-GTR-282) Table 4-3
public domain. Supports: shrinkage.
- USDA FIA REF_SPECIES
public domain. Supports: scientific name.
- GWDD v2.2 (Fischer et al. 2026)
CC BY 4.0. Supports: family.
- USDA FPL — Wood Handbook (2021)
Public domain. Chapters on moisture, mechanical properties, fastenings, design, bonding, drying, decay, preservation, and finishing provide the general workshop background.
- USDA FSIS — Cutting Boards
Public domain. Cleaning, cross-contamination prevention, and board replacement.
Compare before you choose
See how Western redcedar and Northern white cedar differ in hardness, density, strength, and shrinkage, with sources alongside the values.
Compare Western redcedar with Northern white cedarHealth and safety
A published occupational source reports asthma, central nervous system effects, dermatitis, mucous membrane irritation, rhinitis for this wood. What that means, and how strong the link is.
Woods of similar hardness
A substitute must match more than hardness. Compare the shrinkage and the stiffness before you change species.
| # | Wood | Janka | |
|---|---|---|---|
| 1 | Atlantic white cedar | 350 lbf | |
| 2 | Black cottonwood | 350 lbf | |
| 3 | Quaking aspen | 350 lbf | |
| 4 | Subalpine fir | 350 lbf | |
| 5 | Balsam poplar | 351 lbf* | |
| 6 | Batai | 344 lbf* |