Best wood for veneer
Select the face for appearance and the whole panel for balance and stability.

Which wood should you choose?
Walnut, maple, and oak are versatile veneers, while many softer and more decorative species also make excellent faces. Choose the figure, cut, leaf sequence, thickness, and substrate as a complete panel system. High density is not a general test of whether a wood makes good veneer.
Practical wood choices
These editorial choices account for the application as well as the numbers. They may differ from the automated property ranking below.
Walnut
Useful for warm, contrasting faces and traditional bookmatched work. Check leaf sequence, sapwood, and the appearance under finish. A paper-thin sample may not represent the figure across a large panel.
Species profiles:Black walnut
Maple
Available in plain and highly figured forms. Figure can introduce waviness or handling challenges in raw leaves. Test flattening, adhesive, and finish methods with the supplied material.
Species profiles:Sugar maple
Oak
Offers different effects in plain-sliced, rift, and quartered cuts. Ray figure and pore texture influence the final panel. Decide on the cut before comparing prices across suppliers.
Species profiles:White oakNorthern red oak
What matters for this project
Veneer gains support from the core, but it still responds to moisture and stresses the assembly. A balanced construction, suitable adhesive, and stable substrate reduce problems. Raw, backed, and prefinished veneers have different application methods. The visual match can change with lighting, particularly when adjacent leaves reflect differently.
What to check before you buy
Order enough sequential material for the full layout and repairs. Confirm face thickness, backing, usable width, defects, and whether the leaves are flattened. Include the reverse face or balancing layer required by the panel design. Compare the total assembled panel cost, not just the decorative face.
Building and looking after it
Prepare a flat clean substrate, arrange the leaves, and test the pressing method before the final panel. Use the adhesive's specified coverage, pressure, and cure time. Control squeeze-through and avoid excessive sanding of thin faces. Seal and detail edges according to the panel's intended environment.
Mistakes to avoid
The ranking below favors hardness and density because those are available numeric fields; it is a limited comparison, not a veneer-quality scale. It omits slicing behavior, figure, backing, adhesive performance, and panel balance.
Property comparison ranking
Janka at least 1,100 lbf. The score combines hardness divided by 4,000 with density divided by 1,200.
This ranking compares selected properties. Use the practical choices above to check the other requirements of your project.
Species enter when the required fields are present and the rule gives a positive score. An absent wood may lack data or fall outside the scoring range; absence is not proof that it is unsuitable.
The order also uses an editorial availability multiplier, shown in the last column. It changes the order without removing a qualifying species. These scores compare selected properties; they do not evaluate every requirement of the finished project.
| # | Wood | Janka | Density | MOR | MOE | Shrinkage | T/R | Availability |
|---|---|---|---|---|---|---|---|---|
| 1 | Cocobolo | 3,860 lbf* | 69.0 lb/ft³ | — | — | 7.0% | 1.59 | |
| 2 | Ipe | 3,680 lbf | 70.0 lb/ft³ | 25,400 lb/in² | 3.14 ×10⁶ lb/in² | 13.2% | 1.21 | |
| 3 | Cumaru | 3,415 lbf | 66.8 lb/ft³ | 24,371 lb/in² | 2.43 ×10⁶ lb/in² | 13.5% | 1.56 | |
| 4 | Verawood | 5,180 lbf* | 78.0 lb/ft³ | — | — | — | — | |
| 5 | Lignumvitae | 4,500 lbf | 80.0 lb/ft³ | — | — | — | — | |
| 6 | Indian rosewood | 3,170 lbf | 53.0 lb/ft³ | 16,900 lb/in² | 1.78 ×10⁶ lb/in² | 8.5% | 2.15 | |
| 7 | Bubinga | 2,690 lbf | 55.9 lb/ft³ | 22,600 lb/in² | 2.48 ×10⁶ lb/in² | 14.2% | 1.45 | |
| 8 | Canalete | 2,200 lbf | 58.2 lb/ft³ | — | — | 11.6% | 1.85 | |
| 9 | Siamese rosewood | 3,441 lbf* | 68.7 lb/ft³ | — | — | — | — | |
| 10 | Azobe | 3,350 lbf | 70.0 lb/ft³ | 24,500 lb/in² | 2.47 ×10⁶ lb/in² | 17.0% | 1.31 | |
| 11 | Olive | 3,336 lbf* | 67.7 lb/ft³ | — | — | — | — | |
| 12 | Zebrano | 2,139 lbf* | 53.0 lb/ft³ | — | — | — | — | |
| 13 | Purpleheart | 1,860 lbf | 58.0 lb/ft³ | 19,200 lb/in² | 2.27 ×10⁶ lb/in² | 9.9% | 1.91 | |
| 14 | Marishballi | 3,570 lbf | 62.0 lb/ft³ | 27,700 lb/in² | 3.34 ×10⁶ lb/in² | 17.2% | 1.56 | |
| 15 | Jarrah | 1,910 lbf | 54.0 lb/ft³ | 16,200 lb/in² | 1.88 ×10⁶ lb/in² | 18.7% | 1.43 | |
| 16 | African ebony | 3,220 lbf | 63.0 lb/ft³ | 21,200 lb/in² | — | 20.0% | 1.17 | |
| 17 | Holywood | 5,728 lbf* | 87.1 lb/ft³ | — | — | — | — | |
| 18 | Lignum-vitae | 5,728 lbf* | 87.1 lb/ft³ | — | — | — | — | |
| 19 | Mockernut hickory | 1,970 lbf | 50.3 lb/ft³ | 19,200 lb/in² | 2.22 ×10⁶ lb/in² | 17.8% | 1.43 | |
| 20 | Honduras Rosewood | 3,097 lbf* | 63.0 lb/ft³ | — | — | — | — | |
| 21 | Panga Panga | 1,630 lbf | 55.0 lb/ft³ | 16,200 lb/in² | 1.97 ×10⁶ lb/in² | — | 1.87 | |
| 22 | Shagbark hickory | 1,880 lbf | 50.3 lb/ft³ | 20,200 lb/in² | 2.16 ×10⁶ lb/in² | 16.7% | 1.50 | |
| 23 | Partridgewood | 5,868 lbf* | 78.0 lb/ft³ | — | — | — | — | |
| 24 | Brazilian rosewood | 2,720 lbf | 64.1 lb/ft³ | 19,000 lb/in² | 1.88 ×10⁶ lb/in² | 8.5% | 1.59 | |
| 25 | Common boxwood | 2,779 lbf* | 62.2 lb/ft³ | — | — | — | — |
Before you choose a board
Use this ranking to compare the properties listed above. Grain direction, defects, moisture content, board dimensions, and construction also affect performance. Check the species page for the original measurements and any estimate marks, then inspect the actual stock you can buy.
The score does not assess decay resistance, food-contact suitability, heat resistance, or structural load capacity. For outdoor work, check durability and treatment requirements separately. For food-contact items and toys, check the intended finish and published safety information.
Read wood allergy and toxicity sourcesHow to read the measurements
Janka compares resistance to indentation. Density is the mass of a given volume of wood. Modulus of rupture (MOR) describes bending strength in a test specimen. Shrinkage figures describe the change from green to oven-dry wood, and T/R compares tangential with radial shrinkage. They are useful for comparison, but do not directly predict seasonal movement in your finished piece.
These are species-level reference values, not a test of the board you are buying or allowable structural design values. Grain, defects, moisture, dimensions, joints, and treatment can change the result. An asterisk beside Janka marks an estimate; open the species page for its source and method. Use the header settings to switch units.
Frequently asked questions
Does veneer eliminate wood movement?
No. Thin faces move less in absolute thickness, but they still impose stresses on a panel. Suitable cores and a balanced assembly remain important.
Is thicker veneer always better?
It can provide more sanding allowance, but changes handling and stresses. Choose thickness to match the construction method, edge details, and future refinishing needs.
What does a balanced veneered panel mean?
It means designing the faces and core so their stresses are managed as an assembly, rather than applying a decorative face to one side without considering the reverse. The appropriate back depends on the core, face, adhesive, and service conditions. Follow the chosen panel system’s guidance and make a sample where the materials or pressing method are unfamiliar.
Sources and further reading
The application advice is editorial guidance. The references below provide background; each wood's measured values have their own sources on its species page.
- USDA Forest Products Laboratory — Wood Handbook
Background on wood properties, moisture, construction, and finishing.