Best wood for cooking utensils and spoons
Balance comfortable carving, a fine grain, and repeated washing.

Which wood should you choose?
Cherry, hard maple, and beech are practical woods for spoons and spatulas. Cherry is often the easiest starting point for hand carving, while maple offers a firmer working edge. Pick a sound blank with grain following the handle; the direction of the fibers matters more than a decorative figure.
Practical wood choices
These editorial choices account for the application as well as the numbers. They may differ from the automated property ranking below.
Cherry
Carves and scrapes well with sharp tools and develops a warm color. It is a useful all-round choice for serving spoons and cooking utensils when you want a balance of strength and workable hardness.
Species profiles:Black cherry
Hard maple
A durable choice for thin spatula edges and frequently used utensils. Its hardness asks more of carving tools. Buy an identified species instead of assuming every board sold as maple has the same properties.
Species profiles:Sugar mapleBlack maple
Beech
An economical, fine-textured option where it is readily available. It can move noticeably with moisture, so drying and handle orientation deserve care. Choose straight stock and avoid short grain at the neck.
Species profiles:American beechEuropean beech
What matters for this project
Consider the utensil's shape before choosing hardness. A long, narrow handle needs continuous fibers; a deep ladle benefits from a blank whose natural curve follows the bowl. Straight grain is easier to read than curl or burl. A smooth surface comes from clean cutting and careful finishing, rather than simply choosing a dense wood.
What to check before you buy
For dry-carved utensils, select seasoned stock without checks. For green carving, allow an oversized blank to dry slowly before final shaping. Reject wood with unknown preservatives or coatings. A small clear offcut from a reputable lumber supplier is often better value than an exotic spoon blank.
Building and looking after it
Keep adequate thickness where the bowl meets the handle. Raise the grain with a little water, let it dry, and remove the roughness before use. Use any finish according to its intended food-contact application and curing instructions. Wash by hand, dry promptly, and inspect thin edges for splits.
Mistakes to avoid
Avoid porous defects, resin pockets, and unknown species for cooking use. Hardness and shrinkage scores do not establish food suitability, heat resistance, or compatibility with a person's sensitivities. A spoon should not be left against a hot pan or open flame.
Property comparison ranking
Janka 600–1,600 lbf. The score favors hardness near 1,000 lbf (double weight) plus lower volumetric shrinkage.
This score does not assess food-contact suitability, heat exposure, grain direction, treatments, or finishes. Choose identified, sound stock and check the requirements of the finished utensil.
Species enter when the required fields are present and the rule gives a positive score. An absent wood may lack data or fall outside the scoring range; absence is not proof that it is unsuitable.
The order also uses an editorial availability multiplier, shown in the last column. It changes the order without removing a qualifying species. These scores compare selected properties; they do not evaluate every requirement of the finished project.
| # | Wood | Janka | Density | MOR | MOE | Shrinkage | T/R | Availability |
|---|---|---|---|---|---|---|---|---|
| 1 | Teak | 1,000 lbf | 40.0 lb/ft³ | 14,600 lb/in² | 1.55 ×10⁶ lb/in² | 7.0% | 2.32 | |
| 2 | Rubberwood | 915 lbf* | 38.0 lb/ft³ | — | — | 7.4% | 2.22 | |
| 3 | Black walnut | 1,010 lbf | 38.5 lb/ft³ | 14,600 lb/in² | 1.68 ×10⁶ lb/in² | 12.8% | 1.42 | |
| 4 | Black cherry | 950 lbf | 35.0 lb/ft³ | 12,300 lb/in² | 1.49 ×10⁶ lb/in² | 11.5% | 1.92 | |
| 5 | Red maple | 950 lbf | 37.8 lb/ft³ | 13,400 lb/in² | 1.64 ×10⁶ lb/in² | 12.6% | 2.05 | |
| 6 | African mahogany | 830 lbf | 32.0 lb/ft³ | 10,700 lb/in² | 1.40 ×10⁶ lb/in² | 8.8% | 1.80 | |
| 7 | True mahogany | 800 lbf | 41.0 lb/ft³ | 11,500 lb/in² | 1.50 ×10⁶ lb/in² | 7.8% | 1.37 | |
| 8 | Southern red oak | 1,060 lbf | 41.3 lb/ft³ | 10,900 lb/in² | 1.49 ×10⁶ lb/in² | 16.1% | 2.40 | |
| 9 | Slash pine | 869 lbf* | 41.3 lb/ft³ | 16,300 lb/in² | 1.98 ×10⁶ lb/in² | 12.1% | 1.41 | |
| 10 | Longleaf pine | 870 lbf | 41.3 lb/ft³ | 14,500 lb/in² | 1.98 ×10⁶ lb/in² | 12.2% | 1.47 | |
| 11 | Bigleaf maple | 850 lbf | 33.6 lb/ft³ | 10,700 lb/in² | 1.45 ×10⁶ lb/in² | 11.6% | 1.92 | |
| 12 | Hackberry | 880 lbf | 37.1 lb/ft³ | 11,000 lb/in² | 1.19 ×10⁶ lb/in² | 13.8% | 1.85 | |
| 13 | Paper birch | 910 lbf | 38.5 lb/ft³ | 12,300 lb/in² | 1.59 ×10⁶ lb/in² | 16.2% | 1.37 | |
| 14 | Iroko | 1,260 lbf | 43.0 lb/ft³ | 12,400 lb/in² | 1.46 ×10⁶ lb/in² | 8.8% | 1.36 | |
| 15 | Western larch | 830 lbf | 36.3 lb/ft³ | 13,000 lb/in² | 1.87 ×10⁶ lb/in² | 14.0% | 2.02 | |
| 16 | Black ash | 850 lbf | 34.3 lb/ft³ | 12,600 lb/in² | 1.60 ×10⁶ lb/in² | 15.2% | 1.56 | |
| 17 | Chestnut oak | 1,130 lbf | 46.1 lb/ft³ | 13,300 lb/in² | 1.59 ×10⁶ lb/in² | 16.4% | 2.04 | |
| 18 | Green ash | 1,200 lbf | 39.1 lb/ft³ | 14,100 lb/in² | 1.66 ×10⁶ lb/in² | 12.5% | 1.54 | |
| 19 | Black maple | 1,180 lbf | 39.8 lb/ft³ | 13,300 lb/in² | 1.62 ×10⁶ lb/in² | 14.0% | 1.94 | |
| 20 | American elm | 830 lbf | 35.0 lb/ft³ | 11,800 lb/in² | 1.34 ×10⁶ lb/in² | 14.6% | 2.26 | |
| 21 | Sweetgum | 850 lbf | 36.3 lb/ft³ | 12,500 lb/in² | 1.64 ×10⁶ lb/in² | 15.8% | 1.92 | |
| 22 | Black tupelo | 810 lbf | 35.0 lb/ft³ | 9,600 lb/in² | 1.20 ×10⁶ lb/in² | 14.4% | 1.71 | |
| 23 | Imbuia | 950 lbf | 40.0 lb/ft³ | 12,100 lb/in² | 1.41 ×10⁶ lb/in² | 9.0% | 2.22 | |
| 24 | Southern magnolia | 1,020 lbf | 35.0 lb/ft³ | 11,200 lb/in² | 1.40 ×10⁶ lb/in² | 12.3% | 1.22 | |
| 25 | Black oak | 1,210 lbf | 42.6 lb/ft³ | 13,900 lb/in² | 1.64 ×10⁶ lb/in² | 15.1% | 2.52 |
Before you choose a board
Use this ranking to compare the properties listed above. Grain direction, defects, moisture content, board dimensions, and construction also affect performance. Check the species page for the original measurements and any estimate marks, then inspect the actual stock you can buy.
The score does not assess decay resistance, food-contact suitability, heat resistance, or structural load capacity. For outdoor work, check durability and treatment requirements separately. For food-contact items and toys, check the intended finish and published safety information.
Read wood allergy and toxicity sourcesHow to read the measurements
Janka compares resistance to indentation. Density is the mass of a given volume of wood. Modulus of rupture (MOR) describes bending strength in a test specimen. Shrinkage figures describe the change from green to oven-dry wood, and T/R compares tangential with radial shrinkage. They are useful for comparison, but do not directly predict seasonal movement in your finished piece.
These are species-level reference values, not a test of the board you are buying or allowable structural design values. Grain, defects, moisture, dimensions, joints, and treatment can change the result. An asterisk beside Janka marks an estimate; open the species page for its source and method. Use the header settings to switch units.
Frequently asked questions
Should I carve green or dry wood?
Green wood is easier to cut, but the spoon will change shape as it dries. Dry stock gives a more predictable final size at the cost of greater cutting resistance.
Does a wooden spoon need oil?
Oil is optional maintenance rather than waterproofing. Use a product intended for the application and avoid thick coatings that can chip from a working edge.
Sources and further reading
The application advice is editorial guidance. The references below provide background; each wood's measured values have their own sources on its species page.
- USDA Forest Products Laboratory — Wood Handbook
Background on wood properties, moisture, construction, and finishing.